630 Process pumps for tube elements up to 4 bar

Overview

630 range of peristaltic pumps offer four drive options, colour display and intuitive menu structure provide visual status indication and minimal key presses
Flow rates up to 13 l/min at up to 2bar peak pressure
Industrial integration - manual, remote, Analog and digital communication, plus PROFIBUS
Keypad incorporates 3-level security PIN lock
Retractable rollers for easy tube loading and a rugged tool-lockable guard
620RE4 high-performance, accurate, four-roller pumphead with LoadSure® rapid tube element change technology
S, U, Du, Bp and En pumps are IP31 rated cased pumps. SN, UN, DuN, BpN and EnN are IP66 rated cased pumps

Control

Pump drives	630S	630SN	630U	630UN	630Du	630DuN	630Bp	630BpN	630US	630DuS	630En	630EnN
Manual control
Intuitive keypad and color display	•	•	•	•	•	•	•	•	•	•	•	•
Choice of flowrate or speed display	•	•	•	•	•	•	•	•	•	•	•	•
Full calibration with choice of flow units	•	•	•	•	•	•	•	•	•	•	•	•
MemoDose function	•	•	•	•	•	•			•	•
Auto restart facility	•	•	•	•	•	•	•	•	•	•	•	•
Guard switch detection	•	•	•	•	•	•	•	•	•	•	•	•
Leak detection	•	•	•	•	•	•	•	•	•	•	•	•
Remote control	•	•	•	•	•	•	•	•	•	•	•	•
Configurable Start/Stop, leak detector and pressure switch input via contact closure or 5V TTL or 24V industrial logic			•	•	•	•
Configurable Start/Stop, leak detector and pressure switch input via 110V industrial logic									•	•
Configurable Start/Stop and leak detector input via contact closure or 5V TTL or 24V industrial logic Note: Does not include pressure switch											•	•
Direction change and auto/manual toggle input via contact closure or 5V TTL or 24V industrial logic			•	•	•	•
Direction change and auto/manual toggle input via 110V industrial logic									•	•
Remote operation of MemDose (foot/hand-switch or logic input)			•	•	•	•
Four configurable digital status outputs through 24V, 30W relays				•		•
Four configurable digital status outputs through 110V relays									•	•
Software configurable logic outputs			•		•
Remote pressure/flow sensors											•	•
Analogue speed control
Fully configurable inputs; 0-10V or 4-20mA			•	•	•	•			•	•
Analogue outputs; 0-10V, 4-20Ma			•	•	•	•			•	•
Keypad/analogue input scaling (replacement of diaphragm pumps)					•	•				•
Tacho frequency output; 0-1478Hz			•	•	•	•
2x sensor inputs 4-20ma*											•	•
Security
3-level PIN lock	•	•	•	•	•	•	•	•	•	•	•	•
Network communication
RS485 network control						•				•
RS232 network control					•
Digital pump commands (Profibus / EtherNet/IP)
Profibus DP V0							•	•
Communication speeds from 9.6kbit/s up to 12000kbit/s							•	•
Baud Rate (MBPS) 10/100 Full/Half Duplex Operation											•	•
Auto detect bus speed											•	•
Speed set point							•	•			•	•
Speed feedback							•	•			•	•
Flow calibration function							•	•			•	•
Hours run							•	•			•	•
Revolution counter							•	•			•	•
Leak detection							•	•			•	•
Low fluid level alarm							•	•			•	•
Diagnostic feedback							•	•			•	•
EtherNet/IP											•	•
Device Level Ring (DLR)											•	•
Flow Totaliser											•	•

Performance

Flow ranges (l/min)	LoadSure element tubing
	620RE (2 rollers)		620RE4 (4 rollers)
Tubing material, tubing bore (mm)	12mm	17mm	12mm	17mm
Marprene TM, Bioprene TM	0.004-9.8	0.001-16	0.003-8.3	0.004-11
Marprene TL, Bioprene TL	0.004-9.8	0.001-18	0.003-8.3	0.005-12
Pumpsil® silicone	0.004-10	0.001-16	0.003-8.7	0.004-11
GORE STA-PURE PCS™, GORE STA-PURE PFL™, Neoprene	0.004-11	0.001-18	0.003-9.0	0.010-13

Pumphead

620RE LoadSure tube element pumphead

620RE is a high-performance, accurate, two-roller pumphead with LoadSure rapid tube element change technology
4mm wall elements in 12mm or 17mm bore sizes allow pressures up to 4 bar and flow rates up to 18 litre/min
Elements are available with Tri-clamp sanitary fittings; and with Cam and Groove fittings

620RE4 LoadSure tube element pumphead

620RE4 is a high-performance, accurate, four-roller pumphead with LoadSure rapid tube element change technology
4mm wall elements in 12mm or 17mm bore sizes allow pressures up to 4 bar and flow rates up to 13 litre/min with minimized pulsation
Elements are available with industry-standard tri-clamp sanitary fittings; and with Cam and Groove fittings for industry

620R continuous tubing pumphead

620R pumphead accommodates 3.2mm wall continuous tubing in four bore sizes from 6.4mm to 15.9mm, giving up to 16 litre/min flow at up to 2 bar pressure
Tubing is available in eight materials for almost any chemical requirement

620L low pulsation pumphead

620L is a specialist 2 bar, six-roller pumphead designed for accurate dispensing to ±0.5%. Minimal pulsation is achieved by splitting the inlet flow into two tubes passing over twin, offset tracks. The two sets of out-of-phase pulses cancel each other out when the channels merge
Uses 4.0mm wall Y-elements in a choice of six materials
Two single channels are also available
Tubing choices: 8mm, 12mm, and 16mm bore, offering flow rates from 0.002 to 12.4 litre/min
Dispenses 500ml in 3.5 seconds

Drives

Simple-to use HMI requiring minimal key presses to reduce chances of costly errors. Flow proportional to pump speed over 2,650:1 control range. IP31 wipedown pumps and IP66 cased pumps for washdown environments.
630S - IP31 and 630SN - IP66 are simple, plug-in and switch on pumps offering economy of ownership. Ultimate process security with a 3 level PIN lock.
630U - IP31 and 630UN - IP66 with all the features of the S/SN models, plus configurable inputs and outputs.
630Du - IP31 and 630DuN - IP66 with configurable inputs and outputs, plus RS232 and RS484.
630Bp - IP31 and 630BpN - IP66 with real time communication makes your process secure and flexible. Bus speed 9.6 kbits/s up to 12000 kbits/s connectivity
630En – IP31 and 630EnN – IP66 EtherNet/IP connectivity for fast and easy access to pump data over Industrial Ethernet

Tubing

Please refer to datasheets for materials and sizes of continuous tubing and tube elements for each pumphead model.

Pumpsil platinum cured silicone tubing		Laser-etched part number, lot number and use-by-date accuracy Certification USP Class VI, FDA regulations 21 CFR177.2600 for contact with food -20 °C to 80 °C
Bioprene thermoplastic tubing		Fully approved for food and pharmaceutical applications Low permeability 5 °C to 80 °C
PureWeld		Low internal spallation ADCF -20 °C to 80 °C
Marprene long life process tubing		Exceptional long life Wide chemical compatibility, especially resistant to oxidizing agents 5 °C to 80 °C, up to 7 bar
GORE STA-PURE PCS reinforced silicone tubing		Longest available peristaltic tube life Virtually no spallation -20 °C to 80 °C, to 7 bar
GORE STA-PURE PFL reinforced fluoroelastomer tubing		Extreme chemical resistance 50 times longer life than other fluoroelastomers -20 °C to 80 °C, to 4 bar
Neoprene industrial application tubing		Handles abrasive slurries Up to 2 bar 0 °C to 80 °C